Here we have a Zamp Solar Charger. A solar panel comes with the kit and goes on your roof to charge your house batteries. An illuminated red light shows the power is on and a blue lightining blot indicates that your batteries are charging. The charge rate is 13.6 volts. To learn more about your solar panel, watch the video tutorial below.     Is there a How-To video you’d like to see? Let us know in the comment section below and check out last week’s How-To Video.  

  If your RV is not equipped with a surge guard protector, we highly recommend you purchase one. The surge protector isolates any problem that may exist from a voltage spike, current loss and the back on power, which will save your appliances inside your RV. To learn more about the surge protector, watch the video tutorial below.     Is there a How-To video you’d like to see? Let us know in the comment section below and check out last week’s How-To Video.  

  Here’s how to hook up the trailer to shore power: – Locate the power cord – You’ll see the label states that connection is for 110 outlets – You either have a 30 or 50 amp coach. The way to tell your coach has a 30 or 50 amp service is by the number of prongs. (3 for 30, 4 for 50) – Plug in and you’re ready to go * Some campgrounds have a breaker that you need to flip the switch before you plug and unplug Watch the video tutorial to learn what to do if you…

  To properly power up your Roadtrek with 12 volt power or shore power, you need to turn on your power modules. Each one of these represents a separate bank of the battery system. Start by turning the bottom button on (it will illuminate blue), then hit the top reset button. This will activate the system and you will hear a click. If you want to turn the second battery on, repeat the process on the second power module. Now you can operate your coach under one or both of these. To learn more about which ones you need for…

  If you’re running on your generator and then plug your cord into the campsite outlet, it will automatically transfer the power over to your cord. Should you not have an automatic switch, you will have to make the connection manually. To do so, take your power cord and plug it into the coach. The power will then transfer over. To learn more, watch the video tutorial below.     Is there a How-To video you’d like to see? Let us know in the comment section below and check out last week’s How-To Video.  

  Do you want to learn the ins and outs of your generator? Do you have a transfer switch or is your RV manual? Need to learn how and when to service your generator? This video is for you! Watch the tutorial for answers to all these questions and more, as well as the process to start and shut down your generator.     Is there a How-To video you’d like to see? Let us know in the comment section below and check out last week’s How-To Video.  

  Roadtrek has taken boondocking to the next level with the use of lithium batteries. Now you’re able to power up your RV without being plugged into shore power or using a generator. To learn more about this new, amazing feature, watch the video tutorial.     Is there a How-To video you’d like to see? Let us know in the comment section below and check out last week’s How-To Video.  

  Make sure you turn off your air conditioner and electric hot water heater before you unplug your coach or turn off your generator. This will help prevent a circuit breaker from popping. To learn more about your RV power down procedures, watch the video tutorial.     Is there a How-To video you’d like to see? Let us know in the comment section below and check out last week’s How-To Video.  

  If your shore power cord is not hard wired into your RV, you’ll have to plug it into the side of the trailer. Simply match the three inlets on the cord with the port on the trailer, push it in, give it a twist and it will lock into place. Tighten the lock ring for extra security and you’re good to go. To learn more about your shore power cord, watch the video tutorial.     Is there a How-To video you’d like to see? Let us know in the comment section below and check out last week’s How-To Video….

  Your coach may be equipped with a power cord reel. Here’s how it works: – Extend the cord out as far as you need it – Place your chord in the access port to hold it in place and plug in – When leaving your campground, unplug, hit the power cord reel switch and it will automatically retract your cord – That’s it! To learn more about your shore power reel, watch the video tutorial.     Is there a How-To video you’d like to see? Let us know in the comment section below and check out last week’s How-To…